BIS Certification for Hexagon Head Bolts IS 1364 Part 1 - Nirmal Autotech Industries, Rohtak, Haryana

Standphill India successfully completed BIS ISI Mark certification under IS 1364 Part 1 for Nirmal Autotech Industries - a hexagon head bolt manufacturer based at Khewat No. 80/2, Jind Rohtak Road, Near Jio Petrol Pump, Bhagotipur, Rohtak, Haryana 124514. The BIS licence bearing number CM/L 9100283214 was made operative from June 24, 2026. Standphill India managed the complete certification process from factory assessment to final licence grant.

Nirmal Autotech Industries is a hexagon head bolt manufacturer operating from Bhagotipur, on Jind Rohtak Road in Rohtak, Haryana - a city with deep roots in India's automotive components and engineering manufacturing base. Rohtak sits within the National Capital Region's industrial belt and has long supplied fasteners, automotive parts, and engineering hardware to manufacturing units across Haryana, Delhi, and Punjab. The company's name reflects its core market focus - autotech - positioning Nirmal Autotech Industries as a fastener supplier to India's automotive and engineering component supply chain.

Hexagon head bolts are among the most fundamental fasteners in mechanical and structural assembly - used across automotive manufacturing, machinery, construction, and general engineering wherever a threaded fastener of defined strength grade is needed. A bolt that fails under tension or shear load in a critical assembly point is not a minor defect - it is a structural or mechanical failure with downstream safety consequences. BIS certification under IS 1364 Part 1 is the standard that automotive OEMs, machinery manufacturers, and engineering buyers rely on to verify that every certified bolt meets defined dimensional, material, and mechanical performance requirements before it is accepted into their supply chain.

IS 1364 Part 1 is the Bureau of Indian Standards mandatory specification for hexagon head bolts of product grades A and B - covering the complete metric size range from M1.6 to M64. The standard specifies thread dimensions and tolerances, head dimensions, material grade and mechanical property requirements, surface finish, and marking - ensuring that certified bolts perform reliably across the tensile and shear loads expected in their intended application.

BIS certification under IS 1364 Part 1 is mandatory. Automotive OEMs, machinery and equipment manufacturers, structural fabricators, and institutional buyers mandate BIS ISI Mark certified hexagon head bolts as a standard procurement and supply chain qualification requirement.

For full details - BIS Certification for Hexagon Head Bolts - IS 1364 Part 1

Pre-audit gap analysis at the Bhagotipur facility covering raw material grade verification, thread rolling and forging process controls, dimensional inspection across the M1.6 to M64 size range, mechanical property testing including tensile and proof load, surface finish and coating verification, marking and head identification compliance, and documentation against IS 1364 Part 1. All gaps resolved before application. Bolt samples tested at a BIS-recognised laboratory across all applicable parameters - first-attempt clearance. Factory audit supported on-ground at Rohtak. Post-audit follow-up managed to licence operative date June 24, 2026.

Nirmal Autotech Industries is certified. Their hexagon head bolts carry the ISI Mark under IS 1364 Part 1 - legally cleared for every automotive OEM, machinery manufacturer, and structural fabricator that mandates BIS-certified fasteners in their supplier qualification process.

Without a valid IS 1364 Part 1 BIS licence - automotive supply chain audits will disqualify you outright. Machinery manufacturers running quality-gated procurement will not approve your bolts. Government and infrastructure fabrication tenders specify ISI-marked fasteners by name. And uncertified fastener manufacturers remain exposed to BIS enforcement at any point.

Rohtak and Haryana's automotive component ecosystem runs on certified fasteners. The manufacturers with BIS licences get the long-term supply contracts. The ones without lose them to competitors who are certified.

Contact Standphill India today for IS 1364 Part 1 consultation.

One standard. One licence. But rarely the whole compliance picture. Standphill India manages every approval your product needs - BIS ISI Mark, CRS, FMCS, WPC/ETA, BEE, EPR, PESO, CDSCO, TEC, Eco Mark, CEE, LMPC and beyond - under one roof, one team, one timeline.

Over 20 years. 10,000+ certifications. 8,000+ clients. India to the world. The world to India.

Contact Standphill India today for a free consultation.

Hexagon head bolts in Rohtak. Dual-certified medical textiles in Moradabad. Timber frames and fire doors in Kharkhoda, Sonepat. Polyester spun yarn in Ludhiana and Bhawanimandi. Performance shoes across Jalandhar. AUS 32 in Vadodara and Nandigama. Reusable period panties in Tirupur. Fire doors in Ghaziabad, Noida, New Delhi, and Sonepat. PVC geomembranes in Palghar. Safety glass in Bengaluru and Sitarganj. Smart meters in Bengaluru. Pharma foils in Noida. Aluminium food packaging foil in Ghaziabad and Nashik. Woven cement sacks in Nagpur. UPVC windows in Hyderabad. Precast concrete pipes in Nagaland. Stainless steel tubes from South Korea. Horizontal lifeline systems in Vadodara. Toy safety in Jamshedpur, Kolkata, and Noida. Fortified rice kernels in Mirzapur. Galvanized barbed wire in Kanpur.

India to the world. The world to India. Every certification in between.

BIS ISI Mark · CRS Registration · FMCS · WPC/ETA · BEE Star Rating · EPR & E-Waste · PESO · CDSCO · TEC Approval · Eco Mark · CEE · LMPC · and beyond

Standphill India - India's leading compliance consultant. Your single partner for every approval your product needs - wherever in the world you manufacture.

Contact us today for a free consultation.